Back
The Wallwork Group, a vacuum/plasma process specialist, is pioneering a new technology to remove the rough and irregular finish that is typical of additive manufactured (AM) metal components. The project is an international collaboration with the University of Manchester materials science department along with an AM processor in France and dental implant manufacturer in Italy.
Supported by European Commission funding under a Fast-Track to Innovation Pilot, the 29-month programme, starting with a proven process technology, will transfer into live deployment in manufacturing plants. The programme follows on from an earlier Innovate UK supported research project, SEAM, a feasibility study to prove the effectiveness of plasma smoothing metal components made by additive manufacturing processes.
The technical challenge is that AM components, created by sequential fusing of metal powder, have a rough and unattractive surface finish. As the AM process is particularly suited to producing highly complex parts that would be difficult to produce by any other method, these parts are both problematic and expensive to smooth using mechanical techniques and also may require some hand finishing. This time-consuming and costly final processing slows the production cycle and undermines the economic viability of additive manufacturing, sometimes preventing its adoption for many applications.
Wallwork, technical manager, Laurent Espitalier explained, “We have intellectual property in the electrolytic plasma process at the heart of this programme and extensive experience in building vacuum/plasma process equipment. The speed of the process is a clear advantage compared to mechanical finishing so that cycle times can be significantly reduced. Energy use is relatively low, there are no toxic by-products, so the process is very attractive, both commercially and environmentally.”
Wallwork Cambridge operate one of Europe’s largest facilities for the application of advanced micro-thin coatings for aerospace, motorsport and medical applications using physical vapour deposition (PVD) and plasma enhanced chemical vapour deposition (PECVD). The complex machines, software and control systems required for these processes are manufactured and developed by the company. This machine-build and applications experience facilitates rapid commercialisation of the plasma smoothing process, enabling the company to scale-up the patented process and build the bespoke machines required for economic component finishing.
The programme of process development, machine build and live trials to prove the effectiveness of the system in manufacturing environments will last 29 months after which the partners anticipate they will have sufficient data to proceed to full commercial exploitation of the technique.
More Information
Howard Maher, Sales Manager
Tel. +44 (0)161 797 9111 Fax. +44 (0)161 763 1861
E-mail: howard.maher@wallworkht.com Web: www.wallworkht.com
Wallwork Group, Lord Street, Bury, Greater Manchester, BL9 0RE
Images at www.ainsmag.co.uk/client-news/wallwork-group/wallwork-to-lead-international-project-for-additive-manufacturing-smoothing/
10.
April
2017.
International Project to Commercialise Plasma Process for Surface Smoothing of Additive Manufacture Components Goes Live
The Wallwork Group, a vacuum/plasma process specialist, is pioneering a new technology to remove the rough and irregular finish that is typical of additive manufactured (AM) metal components. The project is an international collaboration with the University of Manchester materials science department along with an AM processor in France and dental implant manufacturer in Italy.
Supported by European Commission funding under a Fast-Track to Innovation Pilot, the 29-month programme, starting with a proven process technology, will transfer into live deployment in manufacturing plants. The programme follows on from an earlier Innovate UK supported research project, SEAM, a feasibility study to prove the effectiveness of plasma smoothing metal components made by additive manufacturing processes.
The technical challenge is that AM components, created by sequential fusing of metal powder, have a rough and unattractive surface finish. As the AM process is particularly suited to producing highly complex parts that would be difficult to produce by any other method, these parts are both problematic and expensive to smooth using mechanical techniques and also may require some hand finishing. This time-consuming and costly final processing slows the production cycle and undermines the economic viability of additive manufacturing, sometimes preventing its adoption for many applications.
Wallwork, technical manager, Laurent Espitalier explained, “We have intellectual property in the electrolytic plasma process at the heart of this programme and extensive experience in building vacuum/plasma process equipment. The speed of the process is a clear advantage compared to mechanical finishing so that cycle times can be significantly reduced. Energy use is relatively low, there are no toxic by-products, so the process is very attractive, both commercially and environmentally.”
Wallwork Cambridge operate one of Europe’s largest facilities for the application of advanced micro-thin coatings for aerospace, motorsport and medical applications using physical vapour deposition (PVD) and plasma enhanced chemical vapour deposition (PECVD). The complex machines, software and control systems required for these processes are manufactured and developed by the company. This machine-build and applications experience facilitates rapid commercialisation of the plasma smoothing process, enabling the company to scale-up the patented process and build the bespoke machines required for economic component finishing.
The programme of process development, machine build and live trials to prove the effectiveness of the system in manufacturing environments will last 29 months after which the partners anticipate they will have sufficient data to proceed to full commercial exploitation of the technique.
More Information
Howard Maher, Sales Manager
Tel. +44 (0)161 797 9111 Fax. +44 (0)161 763 1861
E-mail: howard.maher@wallworkht.com Web: www.wallworkht.com
Wallwork Group, Lord Street, Bury, Greater Manchester, BL9 0RE
Images at www.ainsmag.co.uk/client-news/wallwork-group/wallwork-to-lead-international-project-for-additive-manufacturing-smoothing/